Zonet ZEW3003 Specifications

8Chapter 4 Configure your ZEW3003 4.1 Log in ZEW3003 provides Web based configuration scheme configuring by Internet Explorer. 1. Open an Interne

94.2 Status Status page allows you to monitor the current status of ZEW3003 and view the statistics of packets sent and received on LAN and WLAN. 4.

10 4.3 LAN Setup 4.3.1 LAN Setup  System IP address: ZEW3003’s LAN IP address (not your PC’s IP address). Once you modify the IP address, you n

11 4.4 Radio Radio page contains five modes, including AP, Client, WDS, AP+WDS and Repeater. Here are some basic settings:  Radio Band: Select fr

12 4.4.1 AP  IAPP: Enable it to allow wireless station roaming between IAPP enabled access points within the same wireless LAN. In

13 4.4.2 Client  SSID: Default value is default.  Network Type: Select from Infrastructure and Ad-Hoc. Default setting is Infrastructure. In

14 4.4.3 WDS In WDS mode, two ZEW3003 in two remote locations connect with each other to provide a wireless bridge between 2 wired networks. The

15 4.4.4 AP+WDS In AP+WDS mode, ZEW3003 will work both in AP mode and WDS mode. It supports the wireless bridge between the two wired networks; t

16 4.4.5 Repeater  Repeater-SSID: The name for your repeater.  IAPP: Enable it to allow wireless station roaming between IAPP enable

17 4.5 Security Security page contains eight Authentication Types, including None, WEP, WPA SOHO USER, WPA2 SOHO USER, and WPA&WPA2 SO

Copyright Statement is the registered trademark of Zonet Technology Inc. All the products and product names mentioned herein are the trademarks or

18  Key1, 2, 3, 4: Input WEP key characters here, the number of characters must be the same as the number displayed at WEP Mode. You must

19 4.5.4 WPA Personal Wi-Fi Protected Access (WPA) is an advanced security standard. It uses TKIP and AES to change the encryption key frequently.

20 4.5.6 WPA2 Personal WPA2 is a stronger version of WPA.  Accessorial Authentication & Encryption: Default setting is AES.  Key: Enter

21 4.5.8 WPA&WPA2 Personal  Pre-Shared Key: For WPA, default setting is TKIP; for WPA2, default setting is AES.  Key: Enter the key whic

22 4.6 WDS Wireless Distribution System uses wireless media to communicate with other access points, like the Ethernet does. To do this, you

23 4.8 Site Survey Site Survey page provides tool to scan the wireless network. If any Access Point or IBSS is found, you could choose to connect it

24 4.10 Advanced  Frag Threshold: Specify the maximum size of packet during the fragmentation of data to be transmitted. Default value is 2346.

25 4.11 MISC  Login ID & Password Setup: Users can setup the Password for the next login in.  Restore Default / Restart System:  Restore

27 Chapter 5. Troubleshooting Q1: If you have trouble connecting to the Internet, try the following steps. 1. Power off the Cable/DSL modem, ZEW3003

1Table of Contents Chapter 1 Introduction…………………….……………………………………………….2 1.1 Welcome…………………..……………………………………………………………………………………2 1.2 Features…………………

2Chapter 1 Introduction 1.1 Welcome ZEW3003 is fully compliant with IEEE802.11g/b standards. It can help you extend from the wired network to the wir

3Chapter 2 Hardware Installation 2.1 Panel Layout 2.1.1 Front Panel The front panel of ZEW3003 consists of several LED indicators. Name Actio

42.1.2 Rear Panel The rear panel contains the following features. (Viewed from left to right) Name Description Power Connector Power Jack only us

52.4 Hardware Connection Note: Before connecting ZEW3003, be sure to power off your computer, DSL/Cable modem, and ZEW3003. To achieve maximum wirele

6Chapter 3 Configure your computer 3.1 TCP/IP Address Setting Default IP Address: 192.168.1.1 Default Subnet Mask: 255.255.255.0 1. Click St

7 4. Select Internet Protocol (TCP/IP) and click Properties. 5. Select Obtain an IP address automatically and Obtain DNS server add